route(category12-datenbank-server.html) - phpMan

ROUTE(8)              Linux System Administrator's Manual             ROUTE(8)

NAME
       route - show / manipulate the IP routing table
SYNOPSIS
       route [-CFvnNee] [-A family |-4|-6]
       route  [-v] [-A family |-4|-6] add [-net|-host] target [netmask Nm] [gw
              Gw] [metric N] [mss M] [window W] [irtt I] [reject] [mod]  [dyn]
              [reinstate] [[dev] If]
       route  [-v] [-A family |-4|-6] del [-net|-host] target [gw Gw] [netmask
              Nm] [metric N] [[dev] If]
       route  [-V] [--version] [-h] [--help]

NOTE
       This program is obsolete. For replacement check ip route.

DESCRIPTION
       Route manipulates the kernel's IP routing tables.  Its primary  use  is
       to  set up static routes to specific hosts or networks via an interface
       after it has been configured with the ifconfig(8) program.
       When the add or del  options  are  used,  route  modifies  the  routing
       tables.   Without these options, route displays the current contents of
       the routing tables.

OPTIONS
       -A family
              use the specified address family (eg `inet'). Use  route  --help
              for  a  full list. You can use -6 as an alias for --inet6 and -4
              as an alias for -A inet

       -F     operate on the kernel's FIB (Forwarding Information Base)  rout-
              ing table.  This is the default.
       -C     operate on the kernel's routing cache.

       -v     select verbose operation.
       -n     show numerical addresses instead of trying to determine symbolic
              host names. This is useful if you are trying  to  determine  why
              the route to your nameserver has vanished.
       -e     use  netstat(8)-format  for  displaying  the routing table.  -ee
              will generate a very long line  with  all  parameters  from  the
              routing table.

       del    delete a route.
       add    add a new route.
       target the destination network or host. You can provide IP addresses in
              dotted decimal or host/network names.
       -net   the target is a network.
       -host  the target is a host.
       netmask NM
              when adding a network route, the netmask to be used.
       gw GW  route packets via a gateway.  NOTE: The specified  gateway  must
              be reachable first. This usually means that you have to set up a
              static route to the  gateway  beforehand.  If  you  specify  the
              address  of  one  of  your  local interfaces, it will be used to
              decide about the interface to which the packets should be routed
              to. This is a BSDism compatibility hack.
       metric M
              set  the metric field in the routing table (used by routing dae-
              mons) to M.
       mss M  sets MTU (Maximum Transmission Unit) of the route  to  M  bytes.
              Note  that  the current implementation of the route command does
              not allow the option to set the Maximum Segment Size (MSS).
       window W
              set the TCP window size for connections over  this  route  to  W
              bytes.  This  is  typically only used on AX.25 networks and with
              drivers unable to handle back to back frames.
       irtt I set the initial round trip time (irtt) for TCP connections  over
              this  route  to I milliseconds (1-12000). This is typically only
              used on AX.25 networks. If omitted the RFC 1122 default of 300ms
              is used.
       reject install  a  blocking  route,  which will force a route lookup to
              fail.  This is for example used  to  mask  out  networks  before
              using the default route.  This is NOT for firewalling.
       mod, dyn, reinstate
              install  a  dynamic or modified route. These flags are for diag-
              nostic purposes, and are generally only set by routing daemons.
       dev If force the route to be associated with the specified  device,  as
              the kernel will otherwise try to determine the device on its own
              (by checking already existing routes and device  specifications,
              and  where  the  route is added to). In most normal networks you
              won't need this.
              If dev If is the last option on the command line, the  word  dev
              may  be omitted, as it's the default. Otherwise the order of the
              route modifiers (metric - netmask - gw - dev) doesn't matter.

EXAMPLES
       route add -net 127.0.0.0 netmask 255.0.0.0 dev lo
              adds the normal loopback  entry,  using  netmask  255.0.0.0  and
              associated with the "lo" device (assuming this device was previ-
              ously set up correctly with ifconfig(8)).

       route add -net 192.56.76.0 netmask 255.255.255.0 dev eth0
              adds a route to the local network 192.56.76.x via  "eth0".   The
              word "dev" can be omitted here.

       route del default
              deletes the current default route, which is labeled "default" or
              0.0.0.0 in the destination field of the current routing table.

       route add default gw mango-gw
              adds a default route (which will  be  used  if  no  other  route
              matches).   All  packets  using  this  route  will  be gatewayed
              through "mango-gw". The device which will actually be  used  for
              that  route  depends on how we can reach "mango-gw" - the static
              route to "mango-gw" will have to be set up before.

       route add ipx4 sl0
              Adds the route to the "ipx4" host via the SLIP interface (assum-
              ing that "ipx4" is the SLIP host).

       route add -net 192.57.66.0 netmask 255.255.255.0 gw ipx4
              This  command adds the net "192.57.66.x" to be gatewayed through
              the former route to the SLIP interface.

       route add -net 224.0.0.0 netmask 240.0.0.0 dev eth0
              This is an obscure one documented so people know how to  do  it.
              This  sets  all  of  the class D (multicast) IP routes to go via
              "eth0". This is the correct normal  configuration  line  with  a
              multicasting kernel.

       route add -net 10.0.0.0 netmask 255.0.0.0 reject
              This   installs  a  rejecting  route  for  the  private  network
              "10.x.x.x."

OUTPUT
       The output of the kernel routing table is organized  in  the  following
       columns
       Destination
              The destination network or destination host.
       Gateway
              The gateway address or '*' if none set.
       Genmask
              The  netmask  for  the  destination net; '255.255.255.255' for a
              host destination and '0.0.0.0' for the default route.
       Flags  Possible flags include
              U (route is up)
              H (target is a host)
              G (use gateway)
              R (reinstate route for dynamic routing)
              D (dynamically installed by daemon or redirect)
              M (modified from routing daemon or redirect)
              A (installed by addrconf)
              C (cache entry)
              !  (reject route)
       Metric The 'distance' to the target (usually counted in  hops).  It  is
              not  used  by  recent kernels, but may be needed by routing dae-
              mons.
       Ref    Number of references to this route. (Not used in the Linux  ker-
              nel.)
       Use    Count  of lookups for the route.  Depending on the use of -F and
              -C this will be either route cache misses (-F) or hits (-C).
       Iface  Interface to which packets for this route will be sent.
       MSS    Default maximum segment  size  for  TCP  connections  over  this
              route.
       Window Default window size for TCP connections over this route.
       irtt   Initial  RTT  (Round  Trip  Time). The kernel uses this to guess
              about the best TCP protocol parameters without waiting on  (pos-
              sibly slow) answers.
       HH (cached only)
              The  number  of  ARP entries and cached routes that refer to the
              hardware header cache for the cached route. This will be -1 if a
              hardware  address  is not needed for the interface of the cached
              route (e.g. lo).
       Arp (cached only)
              Whether or not the hardware address for the cached route  is  up
              to date.
FILES
       /proc/net/ipv6_route
       /proc/net/route
       /proc/net/rt_cache
SEE ALSO
       ip(8)
HISTORY
       Route  for  Linux  was  originally  written  by  Fred  N.   van Kempen,
       <waltje AT uwalt.org> and then modified by Johannes  Stille  and
       Linus  Torvalds for pl15. Alan Cox added the mss and window options for
       Linux 1.1.22. irtt support and merged with netstat  from  Bernd  Ecken-
       fels.
AUTHOR
       Currently  maintained  by Phil Blundell <Philip.Blundell AT pobox.com> and
       Bernd Eckenfels <net-tools AT lina.de>.

net-tools                         2013-06-15                          ROUTE(8)