huschi.net

STRINGS(1)                   GNU Development Tools                  STRINGS(1)
NAME
       strings - print the strings of printable characters in files.
SYNOPSIS
       strings [-afovV] [-min-len]
               [-n min-len] [--bytes=min-len]
               [-t radix] [--radix=radix]
               [-e encoding] [--encoding=encoding]
               [-U method] [--unicode=method]
               [-] [--all] [--print-file-name]
               [-T bfdname] [--target=bfdname]
               [-w] [--include-all-whitespace]
               [-s] [--output-separatorsep_string]
               [--help] [--version] file...
DESCRIPTION
       For each file given, GNU strings prints the printable character
       sequences that are at least 4 characters long (or the number given with
       the options below) and are followed by an unprintable character.
       Depending upon how the strings program was configured it will default
       to either displaying all the printable sequences that it can find in
       each file, or only those sequences that are in loadable, initialized
       data sections.  If the file type in unrecognizable, or if strings is
       reading from stdin then it will always display all of the printable
       sequences that it can find.
       For backwards compatibility any file that occurs after a command line
       option of just - will also be scanned in full, regardless of the
       presence of any -d option.
       strings is mainly useful for determining the contents of non-text
       files.
OPTIONS
       -a
       --all
       -   Scan the whole file, regardless of what sections it contains or
           whether those sections are loaded or initialized.  Normally this is
           the default behaviour, but strings can be configured so that the -d
           is the default instead.
           The - option is position dependent and forces strings to perform
           full scans of any file that is mentioned after the - on the command
           line, even if the -d option has been specified.
       -d
       --data
           Only print strings from initialized, loaded data sections in the
           file.  This may reduce the amount of garbage in the output, but it
           also exposes the strings program to any security flaws that may be
           present in the BFD library used to scan and load sections.  Strings
           can be configured so that this option is the default behaviour.  In
           such cases the -a option can be used to avoid using the BFD library
           and instead just print all of the strings found in the file.
       -f
       --print-file-name
           Print the name of the file before each string.
       --help
           Print a summary of the program usage on the standard output and
           exit.
       -min-len
       -n min-len
       --bytes=min-len
           Print sequences of characters that are at least min-len characters
           long, instead of the default 4.
       -o  Like -t o.  Some other versions of strings have -o act like -t d
           instead.  Since we can not be compatible with both ways, we simply
           chose one.
       -t radix
       --radix=radix
           Print the offset within the file before each string.  The single
           character argument specifies the radix of the offset---o for octal,
           x for hexadecimal, or d for decimal.
       -e encoding
       --encoding=encoding
           Select the character encoding of the strings that are to be found.
           Possible values for encoding are: s = single-7-bit-byte characters
           (ASCII, ISO 8859, etc., default), S = single-8-bit-byte characters,
           b = 16-bit bigendian, l = 16-bit littleendian, B = 32-bit
           bigendian, L = 32-bit littleendian.  Useful for finding wide
           character strings. (l and b apply to, for example, Unicode
           UTF-16/UCS-2 encodings).
       -U [d|i|l|e|x|h]
       --unicode=[default|invalid|locale|escape|hex|highlight]
           Controls the display of UTF-8 encoded mulibyte characters in
           strings.  The default (--unicode=default) is to give them no
           special treatment, and instead rely upon the setting of the
           --encoding option.  The other values for this option automatically
           enable --encoding=S.
           The --unicode=invalid option treats them as non-graphic characters
           and hence not part of a valid string.  All the remaining options
           treat them as valid string characters.
           The --unicode=locale option displays them in the current locale,
           which may or may not support UTF-8 encoding.  The --unicode=hex
           option displays them as hex byte sequences enclosed between <>
           characters.  The --unicode=escape option displays them as escape
           sequences (\uxxxx) and the --unicode=highlight option displays them
           as escape sequences highlighted in red (if supported by the output
           device).  The colouring is intended to draw attention to the
           presence of unicode sequences where they might not be expected.
       -T bfdname
       --target=bfdname
           Specify an object code format other than your system's default
           format.
       -v
       -V
       --version
           Print the program version number on the standard output and exit.
       -w
       --include-all-whitespace
           By default tab and space characters are included in the strings
           that are displayed, but other whitespace characters, such a
           newlines and carriage returns, are not.  The -w option changes this
           so that all whitespace characters are considered to be part of a
           string.
       -s
       --output-separator
           By default, output strings are delimited by a new-line. This option
           allows you to supply any string to be used as the output record
           separator.  Useful with --include-all-whitespace where strings may
           contain new-lines internally.
       @file
           Read command-line options from file.  The options read are inserted
           in place of the original @file option.  If file does not exist, or
           cannot be read, then the option will be treated literally, and not
           removed.
           Options in file are separated by whitespace.  A whitespace
           character may be included in an option by surrounding the entire
           option in either single or double quotes.  Any character (including
           a backslash) may be included by prefixing the character to be
           included with a backslash.  The file may itself contain additional
           @file options; any such options will be processed recursively.
SEE ALSO
       ar(1), nm(1), objdump(1), ranlib(1), readelf(1) and the Info entries
       for binutils.
COPYRIGHT
       Copyright (c) 1991-2018 Free Software Foundation, Inc.
       Permission is granted to copy, distribute and/or modify this document
       under the terms of the GNU Free Documentation License, Version 1.3 or
       any later version published by the Free Software Foundation; with no
       Invariant Sections, with no Front-Cover Texts, and with no Back-Cover
       Texts.  A copy of the license is included in the section entitled "GNU
       Free Documentation License".
binutils-2.30                     2024-11-15                        STRINGS(1)