adjtimex(images) - phpMan

ADJTIMEX(2)                Linux Programmer's Manual               ADJTIMEX(2)

NAME
       adjtimex - tune kernel clock
SYNOPSIS
       #include <sys/timex.h>
       int adjtimex(struct timex *buf);
DESCRIPTION
       Linux  uses  David L. Mills' clock adjustment algorithm (see RFC 1305).
       The system call adjtimex() reads and optionally sets adjustment parame-
       ters  for  this  algorithm.   It  takes a pointer to a timex structure,
       updates kernel parameters from  field  values,  and  returns  the  same
       structure  with  current  kernel values.  This structure is declared as
       follows:
           struct timex {
               int modes;           /* mode selector */
               long offset;         /* time offset (usec) */
               long freq;           /* frequency offset (scaled ppm) */
               long maxerror;       /* maximum error (usec) */
               long esterror;       /* estimated error (usec) */
               int status;          /* clock command/status */
               long constant;       /* pll time constant */
               long precision;      /* clock precision (usec) (read-only) */
               long tolerance;      /* clock frequency tolerance (ppm)
                                       (read-only) */
               struct timeval time; /* current time (read-only) */
               long tick;           /* usecs between clock ticks */
           };
       The modes field determines which parameters, if any, to  set.   It  may
       contain a bitwise-or combination of zero or more of the following bits:
           #define ADJ_OFFSET            0x0001 /* time offset */
           #define ADJ_FREQUENCY         0x0002 /* frequency offset */
           #define ADJ_MAXERROR          0x0004 /* maximum time error */
           #define ADJ_ESTERROR          0x0008 /* estimated time error */
           #define ADJ_STATUS            0x0010 /* clock status */
           #define ADJ_TIMECONST         0x0020 /* pll time constant */
           #define ADJ_TICK              0x4000 /* tick value */
           #define ADJ_OFFSET_SINGLESHOT 0x8001 /* old-fashioned adjtime() */
       Ordinary users are restricted to a zero value for mode.  Only the supe-
       ruser may set any parameters.
RETURN VALUE
       On success, adjtimex() returns the clock state:
           #define TIME_OK   0 /* clock synchronized */
           #define TIME_INS  1 /* insert leap second */
           #define TIME_DEL  2 /* delete leap second */
           #define TIME_OOP  3 /* leap second in progress */
           #define TIME_WAIT 4 /* leap second has occurred */
           #define TIME_BAD  5 /* clock not synchronized */
       On failure, adjtimex() returns -1 and sets errno.
ERRORS
       EFAULT buf does not point to writable memory.
       EINVAL An attempt is made to set buf.offset  to  a  value  outside  the
              range  -131071 to +131071, or to set buf.status to a value other
              than those listed above, or to set buf.tick to a  value  outside
              the  range 900000/HZ to 1100000/HZ, where HZ is the system timer
              interrupt frequency.
       EPERM  buf.mode is nonzero and the  caller  does  not  have  sufficient
              privilege.  Under Linux the CAP_SYS_TIME capability is required.
CONFORMING TO
       adjtimex()  is  Linux-specific  and  should  not  be  used  in programs
       intended to be portable.  See adjtime(3) for a more portable, but  less
       flexible, method of adjusting the system clock.
SEE ALSO
       settimeofday(2), adjtime(3), capabilities(7), time(7)
COLOPHON
       This  page  is  part of release 3.53 of the Linux man-pages project.  A
       description of the project, and information about reporting  bugs,  can
       be found at http://www.kernel.org/doc/man-pages/.

Linux                             2004-05-27                       ADJTIMEX(2)