MPROTECT(feed) - phpMan

MPROTECT(2)                Linux Programmer's Manual               MPROTECT(2)

NAME
       mprotect - set protection on a region of memory
SYNOPSIS
       #include <sys/mman.h>
       int mprotect(void *addr, size_t len, int prot);
DESCRIPTION
       mprotect()  changes protection for the calling process's memory page(s)
       containing  any  part  of   the   address   range   in   the   interval
       [addr, addr+len-1].  addr must be aligned to a page boundary.
       If the calling process tries to access memory in a manner that violates
       the protection, then the kernel generates  a  SIGSEGV  signal  for  the
       process.
       prot  is  either  PROT_NONE  or a bitwise-or of the other values in the
       following list:
       PROT_NONE  The memory cannot be accessed at all.
       PROT_READ  The memory can be read.
       PROT_WRITE The memory can be modified.
       PROT_EXEC  The memory can be executed.
RETURN VALUE
       On success, mprotect() returns zero.  On error,  -1  is  returned,  and
       errno is set appropriately.
ERRORS
       EACCES The  memory cannot be given the specified access.  This can hap-
              pen, for example, if you mmap(2) a file to which you have  read-
              only access, then ask mprotect() to mark it PROT_WRITE.
       EINVAL addr  is  not  a  valid pointer, or not a multiple of the system
              page size.
       ENOMEM Internal kernel structures could not be allocated.
       ENOMEM Addresses in the range [addr, addr+len-1] are  invalid  for  the
              address  space of the process, or specify one or more pages that
              are not mapped.  (Before kernel 2.4.19,  the  error  EFAULT  was
              incorrectly produced for these cases.)
CONFORMING TO
       SVr4,  POSIX.1-2001.   POSIX  says  that  the behavior of mprotect() is
       unspecified if it is applied  to  a  region  of  memory  that  was  not
       obtained via mmap(2).
NOTES
       On  Linux it is always permissible to call mprotect() on any address in
       a process's address space (except for the kernel  vsyscall  area).   In
       particular  it  can  be  used  to  change  existing code mappings to be
       writable.
       Whether PROT_EXEC has any effect different from PROT_READ is  architec-
       ture-  and  kernel  version-dependent.   On some hardware architectures
       (e.g., i386), PROT_WRITE implies PROT_READ.
       POSIX.1-2001 says that an implementation may permit access  other  than
       that specified in prot, but at a minimum can allow write access only if
       PROT_WRITE has been set, and must not allow any access if PROT_NONE has
       been set.
EXAMPLE
       The  program  below  allocates four pages of memory, makes the third of
       these pages read-only, and then  executes  a  loop  that  walks  upward
       through the allocated region modifying bytes.
       An example of what we might see when running the program is the follow-
       ing:
           $ ./a.out
           Start of region:        0x804c000
           Got SIGSEGV at address: 0x804e000
   Program source
       #include <unistd.h>
       #include <signal.h>
       #include <stdio.h>
       #include <malloc.h>
       #include <stdlib.h>
       #include <errno.h>
       #include <sys/mman.h>
       #define handle_error(msg) \
           do { perror(msg); exit(EXIT_FAILURE); } while (0)
       char *buffer;
       static void
       handler(int sig, siginfo_t *si, void *unused)
       {
           printf("Got SIGSEGV at address: 0x%lx\n",
                   (long) si->si_addr);
           exit(EXIT_FAILURE);
       }
       int
       main(int argc, char *argv[])
       {
           char *p;
           int pagesize;
           struct sigaction sa;
           sa.sa_flags = SA_SIGINFO;
           sigemptyset(&sa.sa_mask);
           sa.sa_sigaction = handler;
           if (sigaction(SIGSEGV, &sa, NULL) == -1)
               handle_error("sigaction");
           pagesize = sysconf(_SC_PAGE_SIZE);
           if (pagesize == -1)
               handle_error("sysconf");
           /* Allocate a buffer aligned on a page boundary;
              initial protection is PROT_READ | PROT_WRITE */
           buffer = memalign(pagesize, 4 * pagesize);
           if (buffer == NULL)
               handle_error("memalign");
           printf("Start of region:        0x%lx\n", (long) buffer);
           if (mprotect(buffer + pagesize * 2, pagesize,
                       PROT_READ) == -1)
               handle_error("mprotect");
           for (p = buffer ; ; )
               *(p++) = 'a';
           printf("Loop completed\n");     /* Should never happen */
           exit(EXIT_SUCCESS);
       }
SEE ALSO
       mmap(2), sysconf(3)
COLOPHON
       This page is part of release 3.53 of the Linux  man-pages  project.   A
       description  of  the project, and information about reporting bugs, can
       be found at http://www.kernel.org/doc/man-pages/.

Linux                             2012-08-14                       MPROTECT(2)