sleep.conf.d(feed) - phpMan

SYSTEMD-SLEEP.CONF(5)         systemd-sleep.conf         SYSTEMD-SLEEP.CONF(5)
NAME
       systemd-sleep.conf, sleep.conf.d - Suspend and hibernation
       configuration file
SYNOPSIS
       /etc/systemd/sleep.conf
       /etc/systemd/sleep.conf.d/*.conf
       /run/systemd/sleep.conf.d/*.conf
       /usr/lib/systemd/sleep.conf.d/*.conf
DESCRIPTION
       systemd supports four general power-saving modes:
       suspend
           a low-power state where execution of the OS is paused, and complete
           power loss might result in lost data, and which is fast to enter
           and exit. This corresponds to suspend, standby, or freeze states as
           understood by the kernel.
       hibernate
           a low-power state where execution of the OS is paused, and complete
           power loss does not result in lost data, and which might be slow to
           enter and exit. This corresponds to the hibernation as understood
           by the kernel.
       hybrid-sleep
           a low-power state where execution of the OS is paused, which might
           be slow to enter, and on complete power loss does not result in
           lost data but might be slower to exit in that case. This mode is
           called suspend-to-both by the kernel.
       suspend-then-hibernate
           A low power state where the system is initially suspended (the
           state is stored in RAM). If not interrupted within the delay
           specified by HibernateDelaySec=, the system will be woken using an
           RTC alarm and hibernated (the state is then stored on disk).
       Settings in these files determine what strings will be written to
       /sys/power/disk and /sys/power/state by systemd-sleep(8) when
       systemd(1) attempts to suspend or hibernate the machine. See
       systemd.syntax(5) for a general description of the syntax.
CONFIGURATION DIRECTORIES AND PRECEDENCE
       The default configuration is defined during compilation, so a
       configuration file is only needed when it is necessary to deviate from
       those defaults. By default, the configuration file in /etc/systemd/
       contains commented out entries showing the defaults as a guide to the
       administrator. This file can be edited to create local overrides.
       When packages need to customize the configuration, they can install
       configuration snippets in /usr/lib/systemd/*.conf.d/. Files in /etc/
       are reserved for the local administrator, who may use this logic to
       override the configuration files installed by vendor packages. The main
       configuration file is read before any of the configuration directories,
       and has the lowest precedence; entries in a file in any configuration
       directory override entries in the single configuration file. Files in
       the *.conf.d/ configuration subdirectories are sorted by their filename
       in lexicographic order, regardless of which of the subdirectories they
       reside in. When multiple files specify the same option, for options
       which accept just a single value, the entry in the file with the
       lexicographically latest name takes precedence. For options which
       accept a list of values, entries are collected as they occur in files
       sorted lexicographically. It is recommended to prefix all filenames in
       those subdirectories with a two-digit number and a dash, to simplify
       the ordering of the files.
       To disable a configuration file supplied by the vendor, the recommended
       way is to place a symlink to /dev/null in the configuration directory
       in /etc/, with the same filename as the vendor configuration file.
OPTIONS
       The following options can be configured in the "[Sleep]" section of
       /etc/systemd/sleep.conf or a sleep.conf.d file:
       SuspendMode=, HibernateMode=, HybridSleepMode=
           The string to be written to /sys/power/disk by, respectively,
           systemd-suspend.service(8), systemd-hibernate.service(8), systemd-
           hybrid-sleep.service(8), or systemd-suspend-then-
           hibernate.service(8). More than one value can be specified by
           separating multiple values with whitespace. They will be tried in
           turn, until one is written without error. If neither succeeds, the
           operation will be aborted.
       SuspendState=, HibernateState=, HybridSleepState=
           The string to be written to /sys/power/state by, respectively,
           systemd-suspend.service(8), systemd-hibernate.service(8), systemd-
           hybrid-sleep.service(8), or systemd-suspend-then-
           hibernate.service(8). More than one value can be specified by
           separating multiple values with whitespace. They will be tried in
           turn, until one is written without error. If neither succeeds, the
           operation will be aborted.
       HibernateDelaySec=
           The amount of time in seconds that will pass before the system is
           automatically put into hibernate when using systemd-suspend-then-
           hibernate.service(8).
EXAMPLE: FREEZE
       Example: to exploit the "freeze" mode added in Linux 3.9, one can use
       systemctl suspend with
           [Sleep]
           SuspendState=freeze
SEE ALSO
       systemd-sleep(8), systemd-suspend.service(8), systemd-
       hibernate.service(8), systemd-hybrid-sleep.service(8), systemd-suspend-
       then-hibernate.service(8), systemd(1), systemd.directives(7)
systemd 239                                              SYSTEMD-SLEEP.CONF(5)