LIMITS.CONF(5) Linux-PAM Manual LIMITS.CONF(5)
NAME
limits.conf - configuration file for the pam_limits module
DESCRIPTION
The pam_limits.so module applies ulimit limits, nice priority and
number of simultaneous login sessions limit to user login sessions.
This description of the configuration file syntax applies to the
/etc/security/limits.conf file and *.conf files in the
/etc/security/limits.d directory.
The syntax of the lines is as follows:
<domain><type><item><value>
The fields listed above should be filled as follows:
<domain>
o a username
o a groupname, with @group syntax. This should not be confused
with netgroups.
o the wildcard *, for default entry.
o the wildcard %, for maxlogins limit only, can also be used with
%group syntax. If the % wildcard is used alone it is identical
to using * with maxsyslogins limit. With a group specified
after % it limits the total number of logins of all users that
are member of the group.
o an uid range specified as <min_uid>:<max_uid>. If min_uid is
omitted, the match is exact for the max_uid. If max_uid is
omitted, all uids greater than or equal min_uid match.
o a gid range specified as @<min_gid>:<max_gid>. If min_gid is
omitted, the match is exact for the max_gid. If max_gid is
omitted, all gids greater than or equal min_gid match. For the
exact match all groups including the user's supplementary
groups are examined. For the range matches only the user's
primary group is examined.
o a gid specified as %:<gid> applicable to maxlogins limit only.
It limits the total number of logins of all users that are
member of the group with the specified gid.
<type>
hard
for enforcing hard resource limits. These limits are set by the
superuser and enforced by the Kernel. The user cannot raise his
requirement of system resources above such values.
soft
for enforcing soft resource limits. These limits are ones that
the user can move up or down within the permitted range by any
pre-existing hard limits. The values specified with this token
can be thought of as default values, for normal system usage.
-
for enforcing both soft and hard resource limits together.
Note, if you specify a type of '-' but neglect to supply the
item and value fields then the module will never enforce any
limits on the specified user/group etc. .
<item>
core
limits the core file size (KB)
data
maximum data size (KB)
fsize
maximum filesize (KB)
memlock
maximum locked-in-memory address space (KB)
nofile
maximum number of open file descriptors
rss
maximum resident set size (KB) (Ignored in Linux 2.4.30 and
higher)
stack
maximum stack size (KB)
cpu
maximum CPU time (minutes)
nproc
maximum number of processes
as
address space limit (KB)
maxlogins
maximum number of logins for this user (this limit does not
apply to user with uid=0)
maxsyslogins
maximum number of all logins on system; user is not allowed to
log-in if total number of all users' logins is greater than
specified number (this limit does not apply to user with uid=0)
priority
the priority to run user process with (negative values boost
process priority)
locks
maximum locked files (Linux 2.4 and higher)
sigpending
maximum number of pending signals (Linux 2.6 and higher)
msgqueue
maximum memory used by POSIX message queues (bytes) (Linux 2.6
and higher)
nice
maximum nice priority allowed to raise to (Linux 2.6.12 and
higher) values: [-20,19]
rtprio
maximum realtime priority allowed for non-privileged processes
(Linux 2.6.12 and higher)
All items support the values -1, unlimited or infinity indicating no
limit, except for priority and nice.
If a hard limit or soft limit of a resource is set to a valid value,
but outside of the supported range of the local system, the system may
reject the new limit or unexpected behavior may occur. If the control
value required is used, the module will reject the login if a limit
could not be set.
In general, individual limits have priority over group limits, so if
you impose no limits for admin group, but one of the members in this
group have a limits line, the user will have its limits set according
to this line.
Also, please note that all limit settings are set per login. They are
not global, nor are they permanent; existing only for the duration of
the session. One exception is the maxlogin option, this one is system
wide. But there is a race, concurrent logins at the same time will not
always be detected as such but only counted as one.
In the limits configuration file, the '#' character introduces a
comment - after which the rest of the line is ignored.
The pam_limits module does report configuration problems found in its
configuration file and errors via syslog(3).
EXAMPLES
These are some example lines which might be specified in
/etc/security/limits.conf.
* soft core 0
* hard nofile 512
@student hard nproc 20
@faculty soft nproc 20
@faculty hard nproc 50
ftp hard nproc 0
@student - maxlogins 4
:123 hard cpu 5000
@500: soft cpu 10000
600:700 hard locks 10
SEE ALSO
pam_limits(8), pam.d(5), pam(8), getrlimit(2)getrlimit(3p)
AUTHOR
pam_limits was initially written by Cristian Gafton <gafton AT redhat.com>
Linux-PAM Manual 04/01/2020 LIMITS.CONF(5)
Linux-Distributionen
Huschi als Linux-Admin